How to Change Kernel Runtime Parameters in a Persistent and Non-Persistent Way

In Part 13 of this LFCS (Linux Foundation Certified Sysadmin) series we explained how to use GRUB to modify the behavior of the system by passing options to the kernel for the ongoing boot process.

Similarly, you can use the command line in a running Linux system to alter certain runtime kernel parameters as a one-time modification, or permanently by editing a configuration file.

Thus, you are allowed to enable or disable kernel parameters on-the-fly without much difficulty when it is needed due to a required change in the way the system is expected to operate.

Introducing the /proc Filesystem

The latest specification of the Filesystem Hierarchy Standard indicates that /proc represents the default method for handling process and system information as well as other kernel and memory information. Particularly, /proc/sys is where you can find all the information about devices, drivers, and some kernel features.

The actual internal structure of /proc/sys depends heavily on the kernel being used, but you are likely to find the following directories inside. In turn, each of them will contain other subdirectories where the values for each parameter category are maintained:

1. dev: parameters for specific devices connected to the machine.
2. fs: filesystem configuration (quotas and inodes, for example).
3. kernel: kernel-specific configuration.
4. net: network configuration.
5. vm: use of the kernel’s virtual memory.

To modify the kernel runtime parameters we will use the sysctl command. The exact number of parameters that can be modified can be viewed with:

# sysctl -a | wc -l

If you want to view the complete list of Kernel parameters, just do:

# sysctl -a 

As the the output of the above command will consist of A LOT of lines, we can use a pipeline followed by less to inspect it more carefully:

# sysctl -a | less

Let’s take a look at the first few lines. Please note that the first characters in each line match the names of the directories inside /proc/sys:

Understand Linux /proc Filesystem

For example, the highlighted line:

dev.cdrom.info = drive name:        	sr0

indicates that sr0 is an alias for the optical drive. In other words, that is how the kernel 「sees」 that drive and uses that name to refer to it.

In the following section we will explain how to change other 「more important」 kernel runtime parameters in Linux.

How to Change or Modify Linux Kernel Runtime Parameteres

Based on what we have explained so far, it is easy to see that the name of a parameter matches the directory structure inside /proc/sys where it can be found.

For example:

dev.cdrom.autoclose → /proc/sys/dev/cdrom/autoclose
net.ipv4.ip_forward → /proc/sys/net/ipv4/ip_forward

Check Linux Kernel Parameters

That said, we can view the value of a particular Linux kernel parameter using either sysctl followed by the name of the parameter or reading the associated file:

# sysctl dev.cdrom.autoclose
# cat /proc/sys/dev/cdrom/autoclose
# sysctl net.ipv4.ip_forward
# cat /proc/sys/net/ipv4/ip_forward

Check Linux Kernel Parameters Set or Modify Linux Kernel Parameters

To set the value for a kernel parameter we can also use sysctl, but using the -w option and followed by the parameter’s name, the equal sign, and the desired value.

Another method consists of using echo to overwrite the file associated with the parameter. In other words, the following methods are equivalent to disable the packet forwarding functionality in our system (which, by the way, should be the default value when a box is not supposed to pass traffic between networks):

# echo 0 > /proc/sys/net/ipv4/ip_forward
# sysctl -w net.ipv4.ip_forward=0

It is important to note that kernel parameters that are set using sysctl will only be enforced during the current session and will disappear when the system is rebooted.

To set these values permanently, edit /etc/sysctl.conf with the desired values. For example, to disable packet forwarding in /etc/sysctl.conf make sure this line appears in the file:

net.ipv4.ip_forward=0

Then run following command to apply the changes to the running configuration.

# sysctl -p

Other examples of important kernel runtime parameters are:

fs.file-max specifies the maximum number of file handles the kernel can allocate for the system. Depending on the intended use of your system (web / database / file server, to name a few examples), you may want to change this value to meet the system’s needs.

Otherwise, you will receive a 「Too many open files」 error message at best, and may prevent the operating system to boot at the worst.

If due to an innocent mistake you find yourself in this last situation, boot in single user mode (as explained in Part 13 – Configure and Troubleshoot Linux Grub Boot Loader) and edit /etc/sysctl.conf as instructed earlier. To set the same restriction on a per-user basis, refer to Part 14 – Monitor and Set Linux Process Limit Usage of this series.

kernel.sysrq is used to enable the SysRq key in your keyboard (also known as the print screen key) so as to allow certain key combinations to invoke emergency actions when the system has become unresponsive.

The default value (16) indicates that the system will honor the Alt+SysRq+key combination and perform the actions listed in the sysrq.c documentation found in kernel.org (where key is one letter in the b-z range). For example, Alt+SysRq+b will reboot the system forcefully (use this as a last resort if your server is unresponsive).

Warning! Do not attempt to press this key combination on a virtual machine because it may force your host system to reboot!

When set to 1, net.ipv4.icmp_echo_ignore_all will ignore ping requests and drop them at the kernel level. This is shown in the below image – note how ping requests are lost after setting this kernel parameter:

Block Ping Requests in Linux

A better and easier way to set individual runtime parameters is using .conf files inside /etc/sysctl.d, grouping them by categories.

For example, instead of setting net.ipv4.ip_forward=0 and net.ipv4.icmp_echo_ignore_all=1 in /etc/sysctl.conf, we can create a new file named net.conf inside /etc/sysctl.d:

# echo "net.ipv4.ip_forward=0" > /etc/sysctl.d/net.conf
# echo "net.ipv4.icmp_echo_ignore_all=1" >> /etc/sysctl.d/net.conf

If you choose to use this approach, do not forget to remove those same lines from /etc/sysctl.conf.

Summary

In this article we have explained how to modify kernel runtime parameters, both persistent and non persistently, using sysctl, /etc/sysctl.conf, and files inside /etc/sysctl.d.

In the sysctl docs you can find more information on the meaning of more variables. Those files represent the most complete source of documentation about the parameters that can be set via sysctl.

Did you find this article useful? We surely hope you did. Don’t hesitate to let us know if you have any questions or suggestions to improve.

Become a Linux Certified System Administrator